Judul : Russia VS US Jet Fighter : SuperSonic Boom Speed And Extreme High Manuevers
link : Russia VS US Jet Fighter : SuperSonic Boom Speed And Extreme High Manuevers
Russia VS US Jet Fighter : SuperSonic Boom Speed And Extreme High Manuevers
Military Update News : SU-35, SU-30 VS F-35 , F-22 : Super Sonic Boom Speed And Extreme High Manuevers
Supersonic flight
Supersonic aerodynamics is simpler than subsonic aerodynamics because the airsheets at different points along the plane often can't affect each other. Supersonic jets and rocket vehicles require several times greater thrust to push through the extra aerodynamic drag experienced within the transonic region (around Mach 0.85–1.2). At these speeds aerospace engineers can gently guide air around the fuselage of the aircraft without producing new shock waves but any change in cross area farther down the vehicle leads to shock waves along the body. Designers use the Supersonic area rule and the Whitcomb area rule to minimize sudden changes in size.
The sound source has now broken through the sound speed barrier, and is traveling at 1.4 times the speed of sound, c (Mach 1.4). Because the source is moving faster than the sound waves it creates, it actually leads the advancing wavefront. The sound source will pass by a stationary observer before the observer actually hears the sound it creates.
However, in practical applications, a supersonic aircraft will have to operate stably in both subsonic and supersonic profiles, hence aerodynamic design is more complex.
One problem with sustained supersonic flight is the generation of heat in flight. At high speeds aerodynamic heating can occur, so an aircraft must be designed to operate and function under very high temperatures. Duralumin, the traditional aircraft material, starts to lose strength and go into plastic deformation at relatively low temperatures, and is unsuitable for continuous use at speeds above Mach 2.2 to 2.4. Materials such as titanium and stainless steel allow operations at much higher temperatures. For example, the Lockheed SR-71 Blackbird jet could fly continuously at Mach 3.1 while some parts were above 315 °C (600 °F).
Another area of concern for continued high-speed operation is the engines. Jet engines create thrust by increasing the temperature of the air they ingest, and as the aircraft speeds up, friction and compression heats this air before it reaches the engines. The maximum allowable temperature of the exhaust is determined by the materials in the turbine at the rear of the engine, so as the aircraft speeds up, the difference in intake and exhaust temperature that the engine can create decreases, and the thrust along with it. Air cooling the turbine area to allow operations at higher temperatures was a key solution, one that continued to improve through the 1950s and on to this day.
Intake design was also a major issue. Normal jet engines can only ingest subsonic air, so for supersonic operation the air has to be slowed down. Ramps or cones in the intake are used to create shock waves that slows the airflow before it reaches the engine. Doing so removes energy from the airflow, causing drag. The key to reducing this drag is to use multiple small oblique shock waves, but this was difficult because the angle they make inside the intake changes with Mach number. In order to efficiently operate across a range of speeds, the shock waves have to be "tuned."
An aircraft able to operate for extended periods at supersonic speeds has a potential range advantage over a similar design operating subsonically. Most of the drag an aircraft sees while speeding up to supersonic speeds occurs just below the speed of sound, due to an aerodynamic effect known as wave drag. An aircraft that can accelerate past this speed sees a significant drag decrease, and can fly supersonically with improved fuel economy. However, due to the way lift is generated supersonically, the lift-to-drag ratio of the aircraft as a whole drops, leading to lower range, offsetting or overturning this advantage.
The key to having low supersonic drag is to properly shape the overall aircraft to be long and thin, and close to a "perfect" shape, the von Karman ogive or Sears-Haack body. This has led to almost every supersonic cruising aircraft looking very similar to every other, with a very long and slender fuselage and large delta wings, cf. SR-71, Concorde, etc. Although not ideal for passenger aircraft, this shaping is quite adaptable for bomber use.
History of supersonic flight
Main article: Sound barrier
CLICK SUBSCRIBE . .. . Update Military News- Subscribe Disini Atau Bisa Langsung Menekan Tombol Youtube Subscribe dan Facebook LIKE Berikut ini...
Sobat baru saja selesai membaca :
Russia VS US Jet Fighter : SuperSonic Boom Speed And Extreme High Manuevers
Cepot rasa sudah cukup pembahasan tentang Russia VS US Jet Fighter : SuperSonic Boom Speed And Extreme High Manuevers dikesempatan ini, moga saja dapat menambah informasi serta wawasan Sobat semuanya. Wookey, kita ketemu lagi di artikel berikutnya ya?.
Telah selesai dibaca: Russia VS US Jet Fighter : SuperSonic Boom Speed And Extreme High Manuevers link yang gunakan: https://cepotpost.blogspot.com/2017/09/russia-vs-us-jet-fighter-supersonic.html